Today’s games put desktop processors to the test. Modern CPUs can run over 5.5 GHz and draw 250W to 320W under extreme load. These pose a significant challenge to the CPU coolers.
If a processor reaches its max temperature, it will automatically throttle itself to prevent damage to its internal architecture made of silicon. In games, this thermal throttling results in annoying micro-stutters, significant decreases in frame rates, and loud fan noise. The correct CPU liquid cooler is crucial for any high-performance build to sustain those high boost speeds, keep noise levels down, and safeguard your gear for long-term gaming performance.
An All-in-One (AIO) is a CPU liquid cooler that works on a closed-loop thermodynamic cycle, which includes conductive, convective, and forced-air heat transfer:
The heat generated by the CPU die travels through the Integrated Heat Spreader (IHS), the Thermal Interface Material (TIM), and then into a precision-machined copper cold plate. High-grade electrolytic tough pitch copper is preferred for its high thermal conductivity, which is about 398 W/m·K. The inside of the copper base has micro-skived fins, which are usually spaced a few tenths of a millimeter apart to increase the surface area with the liquid.
Coolant enters the water block, and the heat is transferred through forced convection, with convective heat transfer coefficients ranging from 500 to 5,000 W/m²K. The coolant mix typically consists of roughly 70% distilled water and 30% propylene glycol, blended with corrosion inhibitors and biocides to mitigate galvanic corrosion between copper and aluminium components..
The hot liquid is cooled at the radiator with a brushless 12V pump, which pushes between 0.8 and 1.2 liters per minute. The fluid flows within the radiator through parallel channels that are attached to the folded aluminum fins, where the efficiency of the fins is 0.8-0.9. Ambient air is then pushed into the fin stack by High-static-pressure Pulse Width Modulation (PWM) fans, removing the heat directly out of the chassis.
Builders need to assess the amount of work they are required to do and decide if they would need a dual-tower air cooler or a closed-loop CPU liquid cooler before choosing a cooling unit. The technologies have come a long way, and both have their own unique thermal envelope.
Premium dual-tower CPU air coolers use four to six pure copper sintered heat pipes, soldered or pressed into a slightly convex, electroplated copper base plate. A good 6-heat-pipe air cooler with twin towers can handle between 160W and 240W of Thermal Design Power (TDP) and maintain a noise level below 33dB(A) even under concentrated mounting pressures applied at the center of the IHS of the processor. Air cooling is an outstanding option for mid-range processors (6-core and 8-core with moderate power limits), which require very little maintenance.
But when it comes to CPUs, there are three situations in which upgrading to a CPU liquid cooler is a must:
|
Specification Metric |
Dual-Tower Air Cooler (6 Heat Pipes) |
240mm CPU Liquid Cooler |
360mm CPU Liquid Cooler |
|
Effective TDP Rating |
160W – 240W |
200W – 240W |
280W – 320W+ |
|
Typical Radiator / Heatsink Size |
Dual 120mm Fin Towers |
277 x 120 x 27 mm |
394–397 x 120 x 27 mm |
|
Acoustic Output (Full Load) |
27 – 33 dB(A) |
At or below 30 dB(A) |
At or below 30 dB(A) |
|
RAM Module Clearance |
Requires high-cutout fins |
100% Unobstructed |
100% Unobstructed |
|
Ideal Gaming CPU Tier |
Core i5 / Ryzen 5 & 7 |
Core i7 / Ryzen 7 |
Core i9 / Core Ultra 9 / Ryzen 9 |
The total surface area available for heat exchange is dependent on the size of the radiator. A standard 240mm CPU liquid cooler (277 x 120 x 27 mm) is capable of handling thermal loads of up to 200W to 240W, which is enough for compact mid-tower and micro-ATX systems.
A 360mm radiator (394 x 120 x 27 mm) is offered for flagships, increasing the thermal dissipation surface by 50% with a thermal load of up to 320W. Watch for radiators that are designed with S-shaped aluminum fins. When compared to traditional V-corrugated louvers, S-louver geometry can increase the contact surface area between the coolant tubes without reducing the airflow through the louver at an optimum 18-20 Fins Per Inch (FPI) louver density.
The internal bearing is the key that determines the noise floor and life of the pump, since it is always spinning during operation. Premium liquid coolers use high-precision ceramic bearings or copper-alloy bearings that rotate at 2,400 to 2,600 RPM. The ceramic shafts are almost friction-free and corrosion-resistant and can be used for up to 70,000 hours.
When considering radiator fans, make sure the fan is a 120mm PWM fan that can provide a wide dynamic range (800 to 1,800 RPM) and a minimum airflow capacity of between 68 and 75 CFM with Fluid Dynamic Bearings (FDB) or hydraulic bearings. For well-designed 360mm coolers, noise levels of 30 dB(A) or lower at full load are in compliance with ISO 7779 and ISO 3744 acoustic measurement standards for information technology equipment, where minimum noise is achieved when 3 fans are spinning at moderate speeds instead of 2 at full RPM.
The biggest problem with budget liquid coolers is that over a period of several years, the coolant leaks through the porous rubber hoses. When housing a CPU in a tight chassis, use a CPU liquid cooler made with thick-walled IIR (Isobutylene Isoprene Rubber) + EPDM (Ethylene Propylene Diene Monomer) tubing or a PTFE (Teflon) inner core with a high-density braided polymer mesh (typically 380mm to 400mm length, 12mm outside diameter). Elastomers made of high-grade EPDM resist thermal aging when exposed to continuous fluids at temperatures over 60°C according to ASTM D2000.
Also, check to ensure that the cooling system is manufactured in accordance with ISO 9001 quality management systems and complies with a multitude of international safety and environmental standards such as CE, UL, RoHS (Directive 2011/65/EU), etc.
The recommended amount of mechanical mounting pressure for modern sockets is established by Intel and AMD for their LGA 1700, LGA 1851, LGA 1200, LGA 115x, AM5, and AM4 sockets and is usually 30 to 50 lbf, and should be applied evenly across the board to prevent uneven expansion of the thermal paste and warping of the motherboard PCB.
The new generation of liquid coolers simplifies installation and monitoring of the system, from a usability and visual perspective, by introducing two significant innovations:
It's a matter of matching the verified thermal capacity of the CPU liquid cooler to the needs of your CPU, along with low-permeation materials and quiet pump engineering. ESGAMING is a performance-driven gaming hardware brand, offering cooling solutions that correspond to the demanding specifications of contemporary esports and enthusiast PC builds, based on professional industry R&D and manufacturing excellence.
Each comes with ISO 9001, SGS, CE, UL, and RoHS certifications, ranging from the extreme heat dissipation of the 320W TDP power of the ESGAMING Torrent 360 to the compact infinity-mirror styling of the Prism 240 to the 240W 6-heat-pipe power of the EZ-T600PRO ARGB dual-tower air cooler.
ESGAMING is actively seeking regional distributors, system integrators, and national brand agents across the globe, and offers the opportunity for partnerships as an Official Brand Agent. Partners will benefit from original, high-demand gaming hardware with exclusive local selling rights, localized pricing power, extensive marketing support, and after-sales technical support without hassle by joining the ESGAMING Global Brand Agency Program. Be sure to check out ESGAMING's official website today to see all of the available CPU cooling models and apply for some brand agency opportunities in your area.